mirror of https://github.com/goodtft/LCD-show.git
update LCD show
This commit is contained in:
lcdwiki
parent
564dce2c35
commit
62be42eb69
|
|
@ -3,7 +3,7 @@ sudo rm -rf /etc/X11/xorg.conf.d/40-libinput.conf
|
|||
sudo mkdir /etc/X11/xorg.conf.d
|
||||
sudo cp ./usr/tft9341-overlay.dtb /boot/overlays/
|
||||
sudo cp ./usr/tft9341-overlay.dtb /boot/overlays/tft9341.dtbo
|
||||
sudo cp -rf ./usr/99-calibration.conf-24 /etc/X11/xorg.conf.d/99-calibration.conf
|
||||
sudo cp -rf ./usr/99-calibration.conf-32 /etc/X11/xorg.conf.d/99-calibration.conf
|
||||
sudo cp -rf ./usr/99-fbturbo.conf /usr/share/X11/xorg.conf.d/
|
||||
if [ -b /dev/mmcblk0p7 ]; then
|
||||
sudo cp ./usr/cmdline.txt-noobs /boot/cmdline.txt
|
||||
|
|
@ -11,7 +11,7 @@ else
|
|||
sudo cp ./usr/cmdline.txt /boot/
|
||||
fi
|
||||
sudo cp ./usr/inittab /etc/
|
||||
sudo cp ./boot/config-28.txt /boot/config.txt
|
||||
sudo cp ./boot/config-32.txt /boot/config.txt
|
||||
nodeplatform=`uname -n`
|
||||
kernel=`uname -r`
|
||||
version=`uname -v`
|
||||
|
|
@ -24,13 +24,7 @@ if test $version -lt 970;then
|
|||
echo "reboot"
|
||||
else
|
||||
echo "need to update touch configuration"
|
||||
if test $version -ge 1023;then
|
||||
echo "install xserver-xorg-input-evdev_2.10.5-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_2.10.5-1_armhf.deb
|
||||
else
|
||||
echo "install xserver-xorg-input-evdev_1%3a2.10.3-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
|
||||
fi
|
||||
sudo apt-get install xserver-xorg-input-evdev
|
||||
sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
|
||||
echo "reboot"
|
||||
fi
|
||||
|
|
|
|||
|
|
@ -3,7 +3,7 @@ sudo rm -rf /etc/X11/xorg.conf.d/40-libinput.conf
|
|||
sudo mkdir /etc/X11/xorg.conf.d
|
||||
sudo cp ./usr/tft9341-overlay.dtb /boot/overlays/
|
||||
sudo cp ./usr/tft9341-overlay.dtb /boot/overlays/tft9341.dtbo
|
||||
sudo cp -rf ./usr/99-calibration.conf-28 /etc/X11/xorg.conf.d/99-calibration.conf
|
||||
sudo cp -rf ./usr/99-calibration.conf-32 /etc/X11/xorg.conf.d/99-calibration.conf
|
||||
sudo cp -rf ./usr/99-fbturbo.conf /usr/share/X11/xorg.conf.d/
|
||||
if [ -b /dev/mmcblk0p7 ]; then
|
||||
sudo cp ./usr/cmdline.txt-noobs /boot/cmdline.txt
|
||||
|
|
@ -11,7 +11,7 @@ else
|
|||
sudo cp ./usr/cmdline.txt /boot/
|
||||
fi
|
||||
sudo cp ./usr/inittab /etc/
|
||||
sudo cp ./boot/config-28.txt /boot/config.txt
|
||||
sudo cp ./boot/config-32.txt /boot/config.txt
|
||||
nodeplatform=`uname -n`
|
||||
kernel=`uname -r`
|
||||
version=`uname -v`
|
||||
|
|
@ -24,13 +24,7 @@ if test $version -lt 970;then
|
|||
echo "reboot"
|
||||
else
|
||||
echo "need to update touch configuration"
|
||||
if test $version -ge 1023;then
|
||||
echo "install xserver-xorg-input-evdev_2.10.5-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_2.10.5-1_armhf.deb
|
||||
else
|
||||
echo "install xserver-xorg-input-evdev_1%3a2.10.3-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
|
||||
fi
|
||||
sudo apt-get install xserver-xorg-input-evdev
|
||||
sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
|
||||
echo "reboot"
|
||||
fi
|
||||
|
|
|
|||
|
|
@ -24,13 +24,7 @@ if test $version -lt 970;then
|
|||
echo "reboot"
|
||||
else
|
||||
echo "need to update touch configuration"
|
||||
if test $version -ge 1023;then
|
||||
echo "install xserver-xorg-input-evdev_2.10.5-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_2.10.5-1_armhf.deb
|
||||
else
|
||||
echo "install xserver-xorg-input-evdev_1%3a2.10.3-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
|
||||
fi
|
||||
sudo apt-get install xserver-xorg-input-evdev
|
||||
sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
|
||||
echo "reboot"
|
||||
fi
|
||||
|
|
|
|||
|
|
@ -24,13 +24,7 @@ if test $version -lt 970;then
|
|||
echo "reboot"
|
||||
else
|
||||
echo "need to update touch configuration"
|
||||
if test $version -ge 1023;then
|
||||
echo "install xserver-xorg-input-evdev_2.10.5-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_2.10.5-1_armhf.deb
|
||||
else
|
||||
echo "install xserver-xorg-input-evdev_1%3a2.10.3-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
|
||||
fi
|
||||
sudo apt-get install xserver-xorg-input-evdev
|
||||
sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
|
||||
echo "reboot"
|
||||
fi
|
||||
|
|
|
|||
|
|
@ -22,13 +22,7 @@ if test $version -lt 970;then
|
|||
echo "reboot"
|
||||
else
|
||||
echo "need to update touch configuration"
|
||||
if test $version -ge 1023;then
|
||||
echo "install xserver-xorg-input-evdev_2.10.5-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_2.10.5-1_armhf.deb
|
||||
else
|
||||
echo "install xserver-xorg-input-evdev_1%3a2.10.3-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
|
||||
fi
|
||||
sudo apt-get install xserver-xorg-input-evdev
|
||||
sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
|
||||
echo "reboot"
|
||||
fi
|
||||
|
|
|
|||
|
|
@ -18,13 +18,7 @@ if test $version -lt 970;then
|
|||
echo "reboot"
|
||||
else
|
||||
echo "need to update touch configuration"
|
||||
if test $version -ge 1023;then
|
||||
echo "install xserver-xorg-input-evdev_2.10.5-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_2.10.5-1_armhf.deb
|
||||
else
|
||||
echo "install xserver-xorg-input-evdev_1%3a2.10.3-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
|
||||
fi
|
||||
sudo apt-get install xserver-xorg-input-evdev
|
||||
fi
|
||||
fi
|
||||
sudo mkdir /etc/X11/xorg.conf.d
|
||||
|
|
|
|||
|
|
@ -20,13 +20,7 @@ if test $version -lt 970;then
|
|||
echo "reboot"
|
||||
else
|
||||
echo "need to update touch configuration"
|
||||
if test $version -ge 1023;then
|
||||
echo "install xserver-xorg-input-evdev_2.10.5-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_2.10.5-1_armhf.deb
|
||||
else
|
||||
echo "install xserver-xorg-input-evdev_1%3a2.10.3-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
|
||||
fi
|
||||
sudo apt-get install xserver-xorg-input-evdev
|
||||
fi
|
||||
fi
|
||||
sudo mkdir /etc/X11/xorg.conf.d
|
||||
|
|
|
|||
|
|
@ -0,0 +1,45 @@
|
|||
#!/bin/bash
|
||||
sudo rm -rf /etc/X11/xorg.conf.d/40-libinput.conf
|
||||
sudo mkdir -p /etc/X11/xorg.conf.d
|
||||
sudo cp ./usr/mhs24-overlay.dtb /boot/overlays/
|
||||
sudo cp ./usr/mhs24-overlay.dtb /boot/overlays/mhs24.dtbo
|
||||
sudo cp -rf ./usr/99-calibration.conf-mhs24 /etc/X11/xorg.conf.d/99-calibration.conf
|
||||
sudo cp -rf ./usr/99-fbturbo-fbcp.conf /usr/share/X11/xorg.conf.d/99-fbturbo.conf
|
||||
if [ -b /dev/mmcblk0p7 ]; then
|
||||
sudo cp ./usr/cmdline.txt-noobs /boot/cmdline.txt
|
||||
else
|
||||
sudo cp ./usr/cmdline.txt /boot/
|
||||
fi
|
||||
sudo cp ./usr/inittab /etc/
|
||||
sudo cp ./boot/config-mhs24.txt /boot/config.txt
|
||||
#FBCP install
|
||||
sudo cp -rf ./etc/rc.local /etc/rc.local
|
||||
sudo apt-get install git cmake -y
|
||||
sudo rm -rf rpi-fbcp
|
||||
sudo git clone https://github.com/tasanakorn/rpi-fbcp
|
||||
sudo mkdir ./rpi-fbcp/build
|
||||
cd ./rpi-fbcp/build/
|
||||
sudo cmake ..
|
||||
sudo make
|
||||
sudo install fbcp /usr/local/bin/fbcp
|
||||
#evdev install
|
||||
nodeplatform=`uname -n`
|
||||
kernel=`uname -r`
|
||||
version=`uname -v`
|
||||
if test "$nodeplatform" = "raspberrypi";then
|
||||
echo "this is raspberrypi kernel"
|
||||
version=${version%% *}
|
||||
version=${version#*#}
|
||||
echo $version
|
||||
if test $version -lt 970;then
|
||||
echo "reboot"
|
||||
else
|
||||
echo "need to update touch configuration"
|
||||
sudo apt-get install xserver-xorg-input-evdev
|
||||
sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
|
||||
echo "reboot"
|
||||
fi
|
||||
else
|
||||
echo "this is not raspberrypi kernel, no need to update touch configure, reboot"
|
||||
fi
|
||||
sudo reboot
|
||||
|
|
@ -0,0 +1,45 @@
|
|||
#!/bin/bash
|
||||
sudo rm -rf /etc/X11/xorg.conf.d/40-libinput.conf
|
||||
sudo mkdir -p /etc/X11/xorg.conf.d
|
||||
sudo cp ./usr/mhs32-overlay.dtb /boot/overlays/
|
||||
sudo cp ./usr/mhs32-overlay.dtb /boot/overlays/mhs32.dtbo
|
||||
sudo cp -rf ./usr/99-calibration.conf-mhs32 /etc/X11/xorg.conf.d/99-calibration.conf
|
||||
sudo cp -rf ./usr/99-fbturbo-fbcp.conf /usr/share/X11/xorg.conf.d/
|
||||
if [ -b /dev/mmcblk0p7 ]; then
|
||||
sudo cp ./usr/cmdline.txt-noobs /boot/cmdline.txt
|
||||
else
|
||||
sudo cp ./usr/cmdline.txt /boot/
|
||||
fi
|
||||
sudo cp ./usr/inittab /etc/
|
||||
sudo cp ./boot/config-mhs32.txt /boot/config.txt
|
||||
#FBCP install
|
||||
sudo cp -rf ./etc/rc.local /etc/rc.local
|
||||
sudo apt-get install git cmake -y
|
||||
sudo rm -rf rpi-fbcp
|
||||
sudo git clone https://github.com/tasanakorn/rpi-fbcp
|
||||
sudo mkdir ./rpi-fbcp/build
|
||||
cd ./rpi-fbcp/build/
|
||||
sudo cmake ..
|
||||
sudo make
|
||||
sudo install fbcp /usr/local/bin/fbcp
|
||||
#evdev install
|
||||
nodeplatform=`uname -n`
|
||||
kernel=`uname -r`
|
||||
version=`uname -v`
|
||||
if test "$nodeplatform" = "raspberrypi";then
|
||||
echo "this is raspberrypi kernel"
|
||||
version=${version%% *}
|
||||
version=${version#*#}
|
||||
echo $version
|
||||
if test $version -lt 970;then
|
||||
echo "reboot"
|
||||
else
|
||||
echo "need to update touch configuration"
|
||||
sudo apt-get install xserver-xorg-input-evdev
|
||||
sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
|
||||
echo "reboot"
|
||||
fi
|
||||
else
|
||||
echo "this is not raspberrypi kernel, no need to update touch configure, reboot"
|
||||
fi
|
||||
sudo reboot
|
||||
|
|
@ -0,0 +1,92 @@
|
|||
#!/bin/bash
|
||||
|
||||
sudo ./system_backup.sh
|
||||
|
||||
if [ -f /etc/X11/xorg.conf.d/40-libinput.conf ]; then
|
||||
sudo rm -rf /etc/X11/xorg.conf.d/40-libinput.conf
|
||||
fi
|
||||
if [ ! -d /etc/X11/xorg.conf.d ]; then
|
||||
sudo mkdir -p /etc/X11/xorg.conf.d
|
||||
fi
|
||||
sudo cp ./usr/mhs35-overlay.dtb /boot/overlays/
|
||||
sudo cp ./usr/mhs35-overlay.dtb /boot/overlays/mhs35.dtbo
|
||||
|
||||
sudo cp -rf ./boot/config-nomal.txt ./boot/config.txt.bak
|
||||
sudo echo "hdmi_force_hotplug=1" >> ./boot/config.txt.bak
|
||||
sudo echo "dtparam=i2c_arm=on" >> ./boot/config.txt.bak
|
||||
sudo echo "dtparam=spi=on" >> ./boot/config.txt.bak
|
||||
sudo echo "enable_uart=1" >> ./boot/config.txt.bak
|
||||
sudo echo "dtoverlay=mhs35:rotate=90" >> ./boot/config.txt.bak
|
||||
sudo echo "hdmi_group=2" >> ./boot/config.txt.bak
|
||||
sudo echo "hdmi_mode=1" >> ./boot/config.txt.bak
|
||||
sudo echo "hdmi_mode=87" >> ./boot/config.txt.bak
|
||||
sudo echo "hdmi_cvt 480 320 60 6 0 0 0" >> ./boot/config.txt.bak
|
||||
sudo echo "hdmi_drive=2" >> ./boot/config.txt.bak
|
||||
sudo cp -rf ./boot/config.txt.bak /boot/config.txt
|
||||
|
||||
sudo cp -rf ./usr/99-calibration.conf-mhs35-90 /etc/X11/xorg.conf.d/99-calibration.conf
|
||||
sudo cp -rf ./usr/99-fbturbo.conf /usr/share/X11/xorg.conf.d/99-fbturbo.conf
|
||||
if [ -b /dev/mmcblk0p7 ]; then
|
||||
sudo cp ./usr/cmdline.txt-noobs /boot/cmdline.txt
|
||||
else
|
||||
sudo cp ./usr/cmdline.txt /boot/
|
||||
fi
|
||||
sudo cp ./usr/inittab /etc/
|
||||
#sudo cp ./boot/config-mhs35.txt /boot/config.txt
|
||||
sudo touch ./.have_installed
|
||||
echo "gpio:resistance:mhs35:90" > ./.have_installed
|
||||
|
||||
#FBCP install
|
||||
wget --spider -q -o /dev/null --tries=1 -T 3 https://github.com
|
||||
if [ $? -eq 0 ]; then
|
||||
sudo cp -rf ./usr/99-fbturbo-fbcp.conf /usr/share/X11/xorg.conf.d/99-fbturbo.conf
|
||||
sudo cp -rf ./etc/rc.local /etc/rc.local
|
||||
sudo apt-get install git cmake -y 2> error_output.txt
|
||||
result=`cat ./error_output.txt`
|
||||
echo -e "\033[31m$result\033[0m"
|
||||
grep -q "^E:" ./error_output.txt && exit
|
||||
sudo rm -rf rpi-fbcp
|
||||
sudo git clone https://github.com/tasanakorn/rpi-fbcp
|
||||
sudo mkdir ./rpi-fbcp/build
|
||||
cd ./rpi-fbcp/build/
|
||||
sudo cmake ..
|
||||
sudo make
|
||||
sudo install fbcp /usr/local/bin/fbcp
|
||||
cd - > /dev/null
|
||||
fi
|
||||
#evdev install
|
||||
nodeplatform=`uname -n`
|
||||
kernel=`uname -r`
|
||||
version=`uname -v`
|
||||
if test "$nodeplatform" = "raspberrypi";then
|
||||
echo "this is raspberrypi kernel"
|
||||
version=${version%% *}
|
||||
version=${version#*#}
|
||||
echo $version
|
||||
if test $version -lt 970;then
|
||||
echo "reboot"
|
||||
else
|
||||
echo "need to update touch configuration"
|
||||
sudo dpkg -i -B ./xserver-xorg-input-evdev_2.10.5-1_armhf.deb 2> error_output.txt
|
||||
#sudo apt-get install xserver-xorg-input-evdev 2> error_output.txt
|
||||
result=`cat ./error_output.txt`
|
||||
echo -e "\033[31m$result\033[0m"
|
||||
grep -q "error:" ./error_output.txt && exit
|
||||
sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
|
||||
#echo "reboot"
|
||||
fi
|
||||
else
|
||||
echo "this is not raspberrypi kernel, no need to update touch configure, reboot"
|
||||
fi
|
||||
|
||||
sudo sync
|
||||
sudo sync
|
||||
sleep 1
|
||||
if [ $# -eq 1 ]; then
|
||||
sudo ./rotate.sh $1
|
||||
elif [ $# -gt 1 ]; then
|
||||
echo "Too many parameters"
|
||||
fi
|
||||
|
||||
echo "reboot now"
|
||||
sudo reboot
|
||||
|
|
@ -0,0 +1,45 @@
|
|||
#!/bin/bash
|
||||
sudo rm -rf /etc/X11/xorg.conf.d/40-libinput.conf
|
||||
sudo mkdir -p /etc/X11/xorg.conf.d
|
||||
sudo cp ./usr/mhs395-overlay.dtb /boot/overlays/
|
||||
sudo cp ./usr/mhs395-overlay.dtb /boot/overlays/mhs395.dtbo
|
||||
sudo cp -rf ./usr/99-calibration.conf-mhs395 /etc/X11/xorg.conf.d/99-calibration.conf
|
||||
sudo cp -rf ./usr/99-fbturbo-fbcp.conf /usr/share/X11/xorg.conf.d/99-fbturbo.conf
|
||||
if [ -b /dev/mmcblk0p7 ]; then
|
||||
sudo cp ./usr/cmdline.txt-noobs /boot/cmdline.txt
|
||||
else
|
||||
sudo cp ./usr/cmdline.txt /boot/
|
||||
fi
|
||||
sudo cp ./usr/inittab /etc/
|
||||
sudo cp ./boot/config-mhs395.txt /boot/config.txt
|
||||
#FBCP install
|
||||
sudo cp -rf ./etc/rc.local /etc/rc.local
|
||||
sudo apt-get install git cmake -y
|
||||
sudo rm -rf rpi-fbcp
|
||||
sudo git clone https://github.com/tasanakorn/rpi-fbcp
|
||||
sudo mkdir ./rpi-fbcp/build
|
||||
cd ./rpi-fbcp/build/
|
||||
sudo cmake ..
|
||||
sudo make
|
||||
sudo install fbcp /usr/local/bin/fbcp
|
||||
#evdev install
|
||||
nodeplatform=`uname -n`
|
||||
kernel=`uname -r`
|
||||
version=`uname -v`
|
||||
if test "$nodeplatform" = "raspberrypi";then
|
||||
echo "this is raspberrypi kernel"
|
||||
version=${version%% *}
|
||||
version=${version#*#}
|
||||
echo $version
|
||||
if test $version -lt 970;then
|
||||
echo "reboot"
|
||||
else
|
||||
echo "need to update touch configuration"
|
||||
sudo apt-get install xserver-xorg-input-evdev
|
||||
sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
|
||||
echo "reboot"
|
||||
fi
|
||||
else
|
||||
echo "this is not raspberrypi kernel, no need to update touch configure, reboot"
|
||||
fi
|
||||
sudo reboot
|
||||
|
|
@ -0,0 +1,45 @@
|
|||
#!/bin/bash
|
||||
sudo rm -rf /etc/X11/xorg.conf.d/40-libinput.conf
|
||||
sudo mkdir -p /etc/X11/xorg.conf.d
|
||||
sudo cp ./usr/mis35-overlay.dtb /boot/overlays/
|
||||
sudo cp ./usr/mis35-overlay.dtb /boot/overlays/mis35.dtbo
|
||||
sudo cp -rf ./usr/99-calibration.conf-mhs35 /etc/X11/xorg.conf.d/99-calibration.conf
|
||||
sudo cp -rf ./usr/99-fbturbo-fbcp.conf /usr/share/X11/xorg.conf.d/99-fbturbo.conf
|
||||
if [ -b /dev/mmcblk0p7 ]; then
|
||||
sudo cp ./usr/cmdline.txt-noobs /boot/cmdline.txt
|
||||
else
|
||||
sudo cp ./usr/cmdline.txt /boot/
|
||||
fi
|
||||
sudo cp ./usr/inittab /etc/
|
||||
sudo cp ./boot/config-mis35.txt /boot/config.txt
|
||||
#FBCP install
|
||||
sudo cp -rf ./etc/rc.local /etc/rc.local
|
||||
sudo apt-get install git cmake -y
|
||||
sudo rm -rf rpi-fbcp
|
||||
sudo git clone https://github.com/tasanakorn/rpi-fbcp
|
||||
sudo mkdir ./rpi-fbcp/build
|
||||
cd ./rpi-fbcp/build/
|
||||
sudo cmake ..
|
||||
sudo make
|
||||
sudo install fbcp /usr/local/bin/fbcp
|
||||
#evdev install
|
||||
nodeplatform=`uname -n`
|
||||
kernel=`uname -r`
|
||||
version=`uname -v`
|
||||
if test "$nodeplatform" = "raspberrypi";then
|
||||
echo "this is raspberrypi kernel"
|
||||
version=${version%% *}
|
||||
version=${version#*#}
|
||||
echo $version
|
||||
if test $version -lt 970;then
|
||||
echo "reboot"
|
||||
else
|
||||
echo "need to update touch configuration"
|
||||
sudo apt-get install xserver-xorg-input-evdev
|
||||
sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
|
||||
echo "reboot"
|
||||
fi
|
||||
else
|
||||
echo "this is not raspberrypi kernel, no need to update touch configure, reboot"
|
||||
fi
|
||||
sudo reboot
|
||||
|
|
@ -22,13 +22,7 @@ if test $version -lt 970;then
|
|||
echo "reboot"
|
||||
else
|
||||
echo "need to update touch configuration"
|
||||
if test $version -ge 1023;then
|
||||
echo "install xserver-xorg-input-evdev_2.10.5-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_2.10.5-1_armhf.deb
|
||||
else
|
||||
echo "install xserver-xorg-input-evdev_1%3a2.10.3-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
|
||||
fi
|
||||
sudo apt-get install xserver-xorg-input-evdev
|
||||
sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
|
||||
echo "reboot"
|
||||
fi
|
||||
|
|
|
|||
|
|
@ -22,13 +22,7 @@ if test $version -lt 970;then
|
|||
echo "reboot"
|
||||
else
|
||||
echo "need to update touch configuration"
|
||||
if test $version -ge 1023;then
|
||||
echo "install xserver-xorg-input-evdev_2.10.5-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_2.10.5-1_armhf.deb
|
||||
else
|
||||
echo "install xserver-xorg-input-evdev_1%3a2.10.3-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
|
||||
fi
|
||||
sudo apt-get install xserver-xorg-input-evdev
|
||||
sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
|
||||
echo "reboot"
|
||||
fi
|
||||
|
|
|
|||
|
|
@ -21,13 +21,7 @@ if test $version -lt 970;then
|
|||
echo "reboot"
|
||||
else
|
||||
echo "need to update touch configuration"
|
||||
if test $version -ge 1023;then
|
||||
echo "install xserver-xorg-input-evdev_2.10.5-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_2.10.5-1_armhf.deb
|
||||
else
|
||||
echo "install xserver-xorg-input-evdev_1%3a2.10.3-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
|
||||
fi
|
||||
sudo apt-get install xserver-xorg-input-evdev
|
||||
sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
|
||||
echo "reboot"
|
||||
fi
|
||||
|
|
|
|||
|
|
@ -1,5 +1,26 @@
|
|||
#!/bin/bash
|
||||
sudo cp -rf ./boot/config-397.txt /boot/config.txt
|
||||
|
||||
sudo ./system_backup.sh
|
||||
|
||||
sudo cp -rf ./boot/config-nomal.txt ./boot/config.txt.bak
|
||||
sudo echo "hdmi_force_hotplug=1" >> ./boot/config.txt.bak
|
||||
sudo echo "hdmi_force_edid_audio=1" >> ./boot/config.txt.bak
|
||||
sudo echo "dtparam=i2c_arm=on" >> ./boot/config.txt.bak
|
||||
sudo echo "dtparam=spi=on" >> ./boot/config.txt.bak
|
||||
sudo echo "enable_uart=1" >> ./boot/config.txt.bak
|
||||
sudo echo "display_rotate=3" >> ./boot/config.txt.bak
|
||||
sudo echo "max_usb_current=1" >> ./boot/config.txt.bak
|
||||
sudo echo "config_hdmi_boost=7" >> ./boot/config.txt.bak
|
||||
sudo echo "hdmi_group=2" >> ./boot/config.txt.bak
|
||||
sudo echo "hdmi_mode=1" >> ./boot/config.txt.bak
|
||||
sudo echo "hdmi_mode=87" >> ./boot/config.txt.bak
|
||||
sudo echo "hdmi_drive=2" >> ./boot/config.txt.bak
|
||||
sudo echo "hdmi_cvt 480 800 60 6 0 0 0" >> ./boot/config.txt.bak
|
||||
sudo echo "dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900" >> ./boot/config.txt.bak
|
||||
sudo cp -rf ./boot/config.txt.bak /boot/config.txt
|
||||
|
||||
#sudo cp -rf ./boot/config-397.txt /boot/config.txt
|
||||
|
||||
if [ -b /dev/mmcblk0p7 ]; then
|
||||
sudo cp ./usr/cmdline.txt-noobs /boot/cmdline.txt
|
||||
else
|
||||
|
|
@ -7,8 +28,13 @@ sudo cp ./usr/cmdline.txt /boot/
|
|||
fi
|
||||
sudo cp ./usr/inittab /etc/
|
||||
sudo cp -rf ./usr/99-fbturbo.conf-HDMI /usr/share/X11/xorg.conf.d/99-fbturbo.conf
|
||||
if [ ! -d /etc/X11/xorg.conf.d ]; then
|
||||
sudo mkdir /etc/X11/xorg.conf.d
|
||||
sudo cp -rf ./usr/99-calibration.conf-397 /etc/X11/xorg.conf.d/99-calibration.conf
|
||||
fi
|
||||
sudo cp -rf ./usr/99-calibration.conf-397-270 /etc/X11/xorg.conf.d/99-calibration.conf
|
||||
sudo touch ./.have_installed
|
||||
echo "hdmi:resistance:397:270" > ./.have_installed
|
||||
|
||||
nodeplatform=`uname -n`
|
||||
kernel=`uname -r`
|
||||
version=`uname -v`
|
||||
|
|
@ -21,17 +47,26 @@ if test $version -lt 970;then
|
|||
echo "reboot"
|
||||
else
|
||||
echo "need to update touch configuration"
|
||||
if test $version -ge 1023;then
|
||||
echo "install xserver-xorg-input-evdev_2.10.5-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_2.10.5-1_armhf.deb
|
||||
else
|
||||
echo "install xserver-xorg-input-evdev_1%3a2.10.3-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
|
||||
fi
|
||||
sudo dpkg -i -B ./xserver-xorg-input-evdev_2.10.5-1_armhf.deb 2> error_output.txt
|
||||
#sudo apt-get install xserver-xorg-input-evdev 2> error_output.txt
|
||||
result=`cat ./error_output.txt`
|
||||
echo -e "\033[31m$result\033[0m"
|
||||
grep -q "error:" ./error_output.txt && exit
|
||||
sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
|
||||
echo "reboot"
|
||||
#echo "reboot"
|
||||
fi
|
||||
else
|
||||
echo "this is not raspberrypi kernel, no need to update touch configure, reboot"
|
||||
fi
|
||||
|
||||
sudo sync
|
||||
sudo sync
|
||||
sleep 1
|
||||
if [ $# -eq 1 ]; then
|
||||
sudo ./rotate.sh $1
|
||||
elif [ $# -gt 1 ]; then
|
||||
echo "Too many parameters"
|
||||
fi
|
||||
|
||||
echo "reboot now"
|
||||
sudo reboot
|
||||
|
|
|
|||
|
|
@ -1,33 +1,39 @@
|
|||
sudo cp -rf ./boot/config-MPI5001.txt /boot/config.txt
|
||||
if [ -b /dev/mmcblk0p7 ]; then
|
||||
sudo cp ./usr/cmdline.txt-noobs /boot/cmdline.txt
|
||||
else
|
||||
sudo cp ./usr/cmdline.txt /boot/
|
||||
fi
|
||||
sudo cp ./usr/inittab /etc/
|
||||
sudo cp -rf ./usr/99-fbturbo.conf-HDMI /usr/share/X11/xorg.conf.d/99-fbturbo.conf
|
||||
#!/bin/bash
|
||||
|
||||
nodeplatform=`uname -n`
|
||||
kernel=`uname -r`
|
||||
version=`uname -v`
|
||||
if test "$nodeplatform" = "raspberrypi";then
|
||||
echo "this is raspberrypi kernel"
|
||||
version=${version%% *}
|
||||
version=${version#*#}
|
||||
echo $version
|
||||
if test $version -lt 970;then
|
||||
echo "reboot"
|
||||
else
|
||||
echo "need to update touch configuration"
|
||||
if test $version -ge 1023;then
|
||||
echo "install xserver-xorg-input-evdev_2.10.5-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_2.10.5-1_armhf.deb
|
||||
else
|
||||
echo "install xserver-xorg-input-evdev_1%3a2.10.3-1"
|
||||
sudo dpkg -i -B xserver-xorg-input-evdev_1%3a2.10.3-1_armhf.deb
|
||||
fi
|
||||
fi
|
||||
fi
|
||||
sudo ./system_backup.sh
|
||||
|
||||
sudo cp -rf ./boot/config-nomal.txt ./boot/config.txt.bak
|
||||
sudo echo "hdmi_force_hotplug=1" >> ./boot/config.txt.bak
|
||||
sudo echo "hdmi_force_edid_audio=1" >> ./boot/config.txt.bak
|
||||
sudo echo "dtparam=i2c_arm=on" >> ./boot/config.txt.bak
|
||||
sudo echo "dtparam=spi=on" >> ./boot/config.txt.bak
|
||||
sudo echo "enable_uart=1" >> ./boot/config.txt.bak
|
||||
sudo echo "display_rotate=0" >> ./boot/config.txt.bak
|
||||
sudo echo "max_usb_current=1" >> ./boot/config.txt.bak
|
||||
sudo echo "config_hdmi_boost=7" >> ./boot/config.txt.bak
|
||||
sudo echo "hdmi_group=2" >> ./boot/config.txt.bak
|
||||
sudo echo "hdmi_mode=1" >> ./boot/config.txt.bak
|
||||
sudo echo "hdmi_mode=87" >> ./boot/config.txt.bak
|
||||
sudo echo "hdmi_drive=2" >> ./boot/config.txt.bak
|
||||
sudo echo "hdmi_cvt 800 480 60 6 0 0 0" >> ./boot/config.txt.bak
|
||||
sudo cp -rf ./boot/config.txt.bak /boot/config.txt
|
||||
#sudo cp -rf ./boot/config-MPI5001.txt /boot/config.txt
|
||||
sudo cp -rf ./usr/99-fbturbo.conf-HDMI /usr/share/X11/xorg.conf.d/99-fbturbo.conf
|
||||
|
||||
if [ ! -d /etc/X11/xorg.conf.d ]; then
|
||||
sudo mkdir /etc/X11/xorg.conf.d
|
||||
sudo cp ./usr/40-libinput.conf-MPI5001 /etc/X11/xorg.conf.d/40-libinput.conf
|
||||
fi
|
||||
sudo cp ./usr/40-libinput.conf-0 /etc/X11/xorg.conf.d/40-libinput.conf
|
||||
sudo touch ./.have_installed
|
||||
echo "hdmi:capacity:MPI5001:0" > ./.have_installed
|
||||
sudo sync
|
||||
sudo sync
|
||||
sleep 1
|
||||
if [ $# -eq 1 ]; then
|
||||
sudo ./rotate.sh $1
|
||||
elif [ $# -gt 1 ]; then
|
||||
echo "Too many parameters"
|
||||
fi
|
||||
|
||||
echo "reboot now"
|
||||
sudo reboot
|
||||
|
|
|
|||
|
|
@ -1,5 +1,12 @@
|
|||
LCD driver for the Raspberry PI Installation<br>
|
||||
====================================================
|
||||
Update: <br>
|
||||
v1.9-20181204<br>
|
||||
Update to support MHS40 & MHS32<br>
|
||||
Update: <br>
|
||||
v1.8-20180907<br>
|
||||
Update to support MHS35<br>
|
||||
Update: <br>
|
||||
v1.7-20180320<br>
|
||||
Update to support Raspbian Version:March 2018(Release date:2018-03-13)<br>
|
||||
Update: <br>
|
||||
|
|
@ -47,6 +54,12 @@ In case of 3.5inch RPi Display(MPI3501)<br>
|
|||
```sudo ./LCD35-show```<br><br>
|
||||
In case of 3.5" HDMI Display-B(MPI3508)<br>
|
||||
```sudo ./MPI3508-show```<br><br>
|
||||
In case of 3.2" High Speed display(MHS32)<br>
|
||||
```sudo ./MHS32-show```<br><br>
|
||||
In case of 3.5" High Speed display(MHS35)<br>
|
||||
```sudo ./MHS35-show```<br><br>
|
||||
In case of 4.0" High Speed display(MHS40)<br>
|
||||
```sudo ./MHS40-show```<br><br>
|
||||
In case of 4.0" HDMI Display(MPI4008)<br>
|
||||
```sudo ./MPI4008-show```<br><br>
|
||||
In case of 5inch HDMI Display-B(Capacitor touch)(MPI5001):<br>
|
||||
|
|
@ -63,7 +76,5 @@ If you need to switch back to the traditional HDMI display<br>
|
|||
Wait a few minutes,the system will restart automaticall , enjoy with your LCD.
|
||||
-------------------------------------------------------------------------------
|
||||
The LCD-show.tar.gz also can be download from:
|
||||
http://www.hellolcd.com/wiki/LCD-show
|
||||
http://www.lcdwiki.com/RaspberryPi-LCD-Driver
|
||||
<br><br>
|
||||
|
||||
|
||||
|
|
|
|||
|
|
@ -54,5 +54,5 @@ enable_uart=1
|
|||
|
||||
# Enable audio (loads snd_bcm2835)
|
||||
dtparam=audio=on
|
||||
dtoverlay=tft9341:rotate=90
|
||||
dtoverlay=tft9341:rotate=270
|
||||
#dtoverlay=ads7846,cs=1,penirq=17,penirq_pull=2,speed=1000000,keep_vref_on=1,swapxy=0,pmax=255,xohms=60,xmin=200,xmax=3900,ymin=200,ymax=3900
|
||||
|
|
|
|||
|
|
@ -22,7 +22,7 @@
|
|||
#framebuffer_height=720
|
||||
|
||||
# uncomment if hdmi display is not detected and composite is being output
|
||||
hdmi_force_hotplug=1
|
||||
#hdmi_force_hotplug=1
|
||||
|
||||
# uncomment to force a specific HDMI mode (this will force VGA)
|
||||
#hdmi_group=1
|
||||
|
|
@ -61,5 +61,6 @@ config_hdmi_boost=7
|
|||
hdmi_group=2
|
||||
hdmi_mode=1
|
||||
hdmi_mode=87
|
||||
hdmi_drive=2
|
||||
hdmi_cvt 480 800 60 6 0 0 0
|
||||
dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900
|
||||
|
|
|
|||
|
|
@ -22,7 +22,7 @@
|
|||
#framebuffer_height=720
|
||||
|
||||
# uncomment if hdmi display is not detected and composite is being output
|
||||
hdmi_force_hotplug=1
|
||||
#hdmi_force_hotplug=1
|
||||
|
||||
# uncomment to force a specific HDMI mode (this will force VGA)
|
||||
#hdmi_group=1
|
||||
|
|
@ -55,6 +55,7 @@ enable_uart=1
|
|||
# Enable audio (loads snd_bcm2835)
|
||||
dtparam=audio=on
|
||||
max_usb_current=1
|
||||
display_rotate=0
|
||||
hdmi_force_hotplug=1
|
||||
config_hdmi_boost=7
|
||||
hdmi_group=2
|
||||
|
|
|
|||
|
|
@ -54,11 +54,13 @@ enable_uart=1
|
|||
|
||||
# Enable audio (loads snd_bcm2835)
|
||||
dtparam=audio=on
|
||||
display_rotate=0
|
||||
max_usb_current=1
|
||||
hdmi_force_hotplug=1
|
||||
config_hdmi_boost=7
|
||||
hdmi_group=2
|
||||
hdmi_mode=1
|
||||
hdmi_mode=87
|
||||
hdmi_drive=1
|
||||
hdmi_cvt 800 480 60 6 0 0 0
|
||||
hdmi_drive=2
|
||||
hdmi_force_edid_audio=1
|
||||
hdmi_cvt 800 480 60 6 0 0 0
|
||||
|
|
|
|||
|
|
@ -0,0 +1,63 @@
|
|||
# For more options and information see
|
||||
# http://www.raspberrypi.org/documentation/configuration/config-txt.md
|
||||
# Some settings may impact device functionality. See link above for details
|
||||
|
||||
# uncomment if you get no picture on HDMI for a default "safe" mode
|
||||
#hdmi_safe=1
|
||||
|
||||
# uncomment this if your display has a black border of unused pixels visible
|
||||
# and your display can output without overscan
|
||||
#disable_overscan=1
|
||||
|
||||
# uncomment the following to adjust overscan. Use positive numbers if console
|
||||
# goes off screen, and negative if there is too much border
|
||||
#overscan_left=16
|
||||
#overscan_right=16
|
||||
#overscan_top=16
|
||||
#overscan_bottom=16
|
||||
|
||||
# uncomment to force a console size. By default it will be display's size minus
|
||||
# overscan.
|
||||
#framebuffer_width=1280
|
||||
#framebuffer_height=720
|
||||
|
||||
# uncomment if hdmi display is not detected and composite is being output
|
||||
hdmi_force_hotplug=1
|
||||
|
||||
# uncomment to force a specific HDMI mode (this will force VGA)
|
||||
#hdmi_group=1
|
||||
#hdmi_mode=1
|
||||
|
||||
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
||||
# DMT (computer monitor) modes
|
||||
#hdmi_drive=2
|
||||
|
||||
# uncomment to increase signal to HDMI, if you have interference, blanking, or
|
||||
# no display
|
||||
#config_hdmi_boost=4
|
||||
|
||||
# uncomment for composite PAL
|
||||
#sdtv_mode=2
|
||||
|
||||
#uncomment to overclock the arm. 700 MHz is the default.
|
||||
#arm_freq=800
|
||||
|
||||
# Uncomment some or all of these to enable the optional hardware interfaces
|
||||
dtparam=i2c_arm=on
|
||||
#dtparam=i2s=on
|
||||
dtparam=spi=on
|
||||
enable_uart=1
|
||||
# Uncomment this to enable the lirc-rpi module
|
||||
#dtoverlay=lirc-rpi
|
||||
|
||||
# Additional overlays and parameters are documented /boot/overlays/README
|
||||
|
||||
# Enable audio (loads snd_bcm2835)
|
||||
dtparam=audio=on
|
||||
dtoverlay=mhs24
|
||||
hdmi_force_hotplug=1
|
||||
hdmi_group=2
|
||||
hdmi_mode=1
|
||||
hdmi_mode=87
|
||||
hdmi_cvt 320 240 60 6 0 0 0
|
||||
hdmi_drive=2
|
||||
|
|
@ -0,0 +1,63 @@
|
|||
# For more options and information see
|
||||
# http://www.raspberrypi.org/documentation/configuration/config-txt.md
|
||||
# Some settings may impact device functionality. See link above for details
|
||||
|
||||
# uncomment if you get no picture on HDMI for a default "safe" mode
|
||||
#hdmi_safe=1
|
||||
|
||||
# uncomment this if your display has a black border of unused pixels visible
|
||||
# and your display can output without overscan
|
||||
#disable_overscan=1
|
||||
|
||||
# uncomment the following to adjust overscan. Use positive numbers if console
|
||||
# goes off screen, and negative if there is too much border
|
||||
#overscan_left=16
|
||||
#overscan_right=16
|
||||
#overscan_top=16
|
||||
#overscan_bottom=16
|
||||
|
||||
# uncomment to force a console size. By default it will be display's size minus
|
||||
# overscan.
|
||||
#framebuffer_width=1280
|
||||
#framebuffer_height=720
|
||||
|
||||
# uncomment if hdmi display is not detected and composite is being output
|
||||
hdmi_force_hotplug=1
|
||||
|
||||
# uncomment to force a specific HDMI mode (this will force VGA)
|
||||
#hdmi_group=1
|
||||
#hdmi_mode=1
|
||||
|
||||
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
||||
# DMT (computer monitor) modes
|
||||
#hdmi_drive=2
|
||||
|
||||
# uncomment to increase signal to HDMI, if you have interference, blanking, or
|
||||
# no display
|
||||
#config_hdmi_boost=4
|
||||
|
||||
# uncomment for composite PAL
|
||||
#sdtv_mode=2
|
||||
|
||||
#uncomment to overclock the arm. 700 MHz is the default.
|
||||
#arm_freq=800
|
||||
|
||||
# Uncomment some or all of these to enable the optional hardware interfaces
|
||||
dtparam=i2c_arm=on
|
||||
#dtparam=i2s=on
|
||||
dtparam=spi=on
|
||||
enable_uart=1
|
||||
# Uncomment this to enable the lirc-rpi module
|
||||
#dtoverlay=lirc-rpi
|
||||
|
||||
# Additional overlays and parameters are documented /boot/overlays/README
|
||||
|
||||
# Enable audio (loads snd_bcm2835)
|
||||
dtparam=audio=on
|
||||
dtoverlay=mhs32
|
||||
hdmi_force_hotplug=1
|
||||
hdmi_group=2
|
||||
hdmi_mode=1
|
||||
hdmi_mode=87
|
||||
hdmi_cvt 480 320 60 6 0 0 0
|
||||
hdmi_drive=2
|
||||
|
|
@ -0,0 +1,63 @@
|
|||
# For more options and information see
|
||||
# http://www.raspberrypi.org/documentation/configuration/config-txt.md
|
||||
# Some settings may impact device functionality. See link above for details
|
||||
|
||||
# uncomment if you get no picture on HDMI for a default "safe" mode
|
||||
#hdmi_safe=1
|
||||
|
||||
# uncomment this if your display has a black border of unused pixels visible
|
||||
# and your display can output without overscan
|
||||
#disable_overscan=1
|
||||
|
||||
# uncomment the following to adjust overscan. Use positive numbers if console
|
||||
# goes off screen, and negative if there is too much border
|
||||
#overscan_left=16
|
||||
#overscan_right=16
|
||||
#overscan_top=16
|
||||
#overscan_bottom=16
|
||||
|
||||
# uncomment to force a console size. By default it will be display's size minus
|
||||
# overscan.
|
||||
#framebuffer_width=1280
|
||||
#framebuffer_height=720
|
||||
|
||||
# uncomment if hdmi display is not detected and composite is being output
|
||||
#hdmi_force_hotplug=1
|
||||
|
||||
# uncomment to force a specific HDMI mode (this will force VGA)
|
||||
#hdmi_group=1
|
||||
#hdmi_mode=1
|
||||
|
||||
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
||||
# DMT (computer monitor) modes
|
||||
#hdmi_drive=2
|
||||
|
||||
# uncomment to increase signal to HDMI, if you have interference, blanking, or
|
||||
# no display
|
||||
#config_hdmi_boost=4
|
||||
|
||||
# uncomment for composite PAL
|
||||
#sdtv_mode=2
|
||||
|
||||
#uncomment to overclock the arm. 700 MHz is the default.
|
||||
#arm_freq=800
|
||||
|
||||
# Uncomment some or all of these to enable the optional hardware interfaces
|
||||
dtparam=i2c_arm=on
|
||||
#dtparam=i2s=on
|
||||
dtparam=spi=on
|
||||
enable_uart=1
|
||||
# Uncomment this to enable the lirc-rpi module
|
||||
#dtoverlay=lirc-rpi
|
||||
|
||||
# Additional overlays and parameters are documented /boot/overlays/README
|
||||
|
||||
# Enable audio (loads snd_bcm2835)
|
||||
dtparam=audio=on
|
||||
dtoverlay=mhs35:rotate=90
|
||||
hdmi_force_hotplug=1
|
||||
hdmi_group=2
|
||||
hdmi_mode=1
|
||||
hdmi_mode=87
|
||||
hdmi_cvt 480 320 60 6 0 0 0
|
||||
hdmi_drive=2
|
||||
|
|
@ -0,0 +1,63 @@
|
|||
# For more options and information see
|
||||
# http://www.raspberrypi.org/documentation/configuration/config-txt.md
|
||||
# Some settings may impact device functionality. See link above for details
|
||||
|
||||
# uncomment if you get no picture on HDMI for a default "safe" mode
|
||||
#hdmi_safe=1
|
||||
|
||||
# uncomment this if your display has a black border of unused pixels visible
|
||||
# and your display can output without overscan
|
||||
#disable_overscan=1
|
||||
|
||||
# uncomment the following to adjust overscan. Use positive numbers if console
|
||||
# goes off screen, and negative if there is too much border
|
||||
#overscan_left=16
|
||||
#overscan_right=16
|
||||
#overscan_top=16
|
||||
#overscan_bottom=16
|
||||
|
||||
# uncomment to force a console size. By default it will be display's size minus
|
||||
# overscan.
|
||||
#framebuffer_width=1280
|
||||
#framebuffer_height=720
|
||||
|
||||
# uncomment if hdmi display is not detected and composite is being output
|
||||
hdmi_force_hotplug=1
|
||||
|
||||
# uncomment to force a specific HDMI mode (this will force VGA)
|
||||
#hdmi_group=1
|
||||
#hdmi_mode=1
|
||||
|
||||
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
||||
# DMT (computer monitor) modes
|
||||
#hdmi_drive=2
|
||||
|
||||
# uncomment to increase signal to HDMI, if you have interference, blanking, or
|
||||
# no display
|
||||
#config_hdmi_boost=4
|
||||
|
||||
# uncomment for composite PAL
|
||||
#sdtv_mode=2
|
||||
|
||||
#uncomment to overclock the arm. 700 MHz is the default.
|
||||
#arm_freq=800
|
||||
|
||||
# Uncomment some or all of these to enable the optional hardware interfaces
|
||||
dtparam=i2c_arm=on
|
||||
#dtparam=i2s=on
|
||||
dtparam=spi=on
|
||||
enable_uart=1
|
||||
# Uncomment this to enable the lirc-rpi module
|
||||
#dtoverlay=lirc-rpi
|
||||
|
||||
# Additional overlays and parameters are documented /boot/overlays/README
|
||||
|
||||
# Enable audio (loads snd_bcm2835)
|
||||
dtparam=audio=on
|
||||
dtoverlay=mhs395
|
||||
hdmi_force_hotplug=1
|
||||
hdmi_group=2
|
||||
hdmi_mode=1
|
||||
hdmi_mode=87
|
||||
hdmi_cvt 480 320 60 6 0 0 0
|
||||
hdmi_drive=2
|
||||
|
|
@ -0,0 +1,63 @@
|
|||
# For more options and information see
|
||||
# http://www.raspberrypi.org/documentation/configuration/config-txt.md
|
||||
# Some settings may impact device functionality. See link above for details
|
||||
|
||||
# uncomment if you get no picture on HDMI for a default "safe" mode
|
||||
#hdmi_safe=1
|
||||
|
||||
# uncomment this if your display has a black border of unused pixels visible
|
||||
# and your display can output without overscan
|
||||
#disable_overscan=1
|
||||
|
||||
# uncomment the following to adjust overscan. Use positive numbers if console
|
||||
# goes off screen, and negative if there is too much border
|
||||
#overscan_left=16
|
||||
#overscan_right=16
|
||||
#overscan_top=16
|
||||
#overscan_bottom=16
|
||||
|
||||
# uncomment to force a console size. By default it will be display's size minus
|
||||
# overscan.
|
||||
#framebuffer_width=1280
|
||||
#framebuffer_height=720
|
||||
|
||||
# uncomment if hdmi display is not detected and composite is being output
|
||||
hdmi_force_hotplug=1
|
||||
|
||||
# uncomment to force a specific HDMI mode (this will force VGA)
|
||||
#hdmi_group=1
|
||||
#hdmi_mode=1
|
||||
|
||||
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
||||
# DMT (computer monitor) modes
|
||||
#hdmi_drive=2
|
||||
|
||||
# uncomment to increase signal to HDMI, if you have interference, blanking, or
|
||||
# no display
|
||||
#config_hdmi_boost=4
|
||||
|
||||
# uncomment for composite PAL
|
||||
#sdtv_mode=2
|
||||
|
||||
#uncomment to overclock the arm. 700 MHz is the default.
|
||||
#arm_freq=800
|
||||
|
||||
# Uncomment some or all of these to enable the optional hardware interfaces
|
||||
dtparam=i2c_arm=on
|
||||
#dtparam=i2s=on
|
||||
dtparam=spi=on
|
||||
enable_uart=1
|
||||
# Uncomment this to enable the lirc-rpi module
|
||||
#dtoverlay=lirc-rpi
|
||||
|
||||
# Additional overlays and parameters are documented /boot/overlays/README
|
||||
|
||||
# Enable audio (loads snd_bcm2835)
|
||||
dtparam=audio=on
|
||||
dtoverlay=mis35
|
||||
hdmi_force_hotplug=1
|
||||
hdmi_group=2
|
||||
hdmi_mode=1
|
||||
hdmi_mode=87
|
||||
hdmi_cvt 480 320 60 6 0 0 0
|
||||
hdmi_drive=2
|
||||
|
|
@ -1,5 +1,5 @@
|
|||
# For more options and information see
|
||||
# http://www.raspberrypi.org/documentation/configuration/config-txt.md
|
||||
# http://rpf.io/configtxt
|
||||
# Some settings may impact device functionality. See link above for details
|
||||
|
||||
# uncomment if you get no picture on HDMI for a default "safe" mode
|
||||
|
|
@ -22,7 +22,7 @@
|
|||
#framebuffer_height=720
|
||||
|
||||
# uncomment if hdmi display is not detected and composite is being output
|
||||
hdmi_force_hotplug=1
|
||||
#hdmi_force_hotplug=1
|
||||
|
||||
# uncomment to force a specific HDMI mode (this will force VGA)
|
||||
#hdmi_group=1
|
||||
|
|
@ -43,10 +43,10 @@ hdmi_force_hotplug=1
|
|||
#arm_freq=800
|
||||
|
||||
# Uncomment some or all of these to enable the optional hardware interfaces
|
||||
dtparam=i2c_arm=on
|
||||
#dtparam=i2c_arm=on
|
||||
#dtparam=i2s=on
|
||||
dtparam=spi=on
|
||||
enable_uart=1
|
||||
#dtparam=spi=on
|
||||
|
||||
# Uncomment this to enable the lirc-rpi module
|
||||
#dtoverlay=lirc-rpi
|
||||
|
||||
|
|
|
|||
|
|
@ -0,0 +1,66 @@
|
|||
# For more options and information see
|
||||
# http://rpf.io/configtxt
|
||||
# Some settings may impact device functionality. See link above for details
|
||||
|
||||
# uncomment if you get no picture on HDMI for a default "safe" mode
|
||||
#hdmi_safe=1
|
||||
|
||||
# uncomment this if your display has a black border of unused pixels visible
|
||||
# and your display can output without overscan
|
||||
#disable_overscan=1
|
||||
|
||||
# uncomment the following to adjust overscan. Use positive numbers if console
|
||||
# goes off screen, and negative if there is too much border
|
||||
#overscan_left=16
|
||||
#overscan_right=16
|
||||
#overscan_top=16
|
||||
#overscan_bottom=16
|
||||
|
||||
# uncomment to force a console size. By default it will be display's size minus
|
||||
# overscan.
|
||||
#framebuffer_width=1280
|
||||
#framebuffer_height=720
|
||||
|
||||
# uncomment if hdmi display is not detected and composite is being output
|
||||
#hdmi_force_hotplug=1
|
||||
|
||||
# uncomment to force a specific HDMI mode (this will force VGA)
|
||||
#hdmi_group=1
|
||||
#hdmi_mode=1
|
||||
|
||||
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
||||
# DMT (computer monitor) modes
|
||||
#hdmi_drive=2
|
||||
|
||||
# uncomment to increase signal to HDMI, if you have interference, blanking, or
|
||||
# no display
|
||||
#config_hdmi_boost=4
|
||||
|
||||
# uncomment for composite PAL
|
||||
#sdtv_mode=2
|
||||
|
||||
#uncomment to overclock the arm. 700 MHz is the default.
|
||||
#arm_freq=800
|
||||
|
||||
# Uncomment some or all of these to enable the optional hardware interfaces
|
||||
#dtparam=i2c_arm=on
|
||||
#dtparam=i2s=on
|
||||
#dtparam=spi=on
|
||||
|
||||
# Uncomment this to enable the lirc-rpi module
|
||||
#dtoverlay=lirc-rpi
|
||||
|
||||
# Additional overlays and parameters are documented /boot/overlays/README
|
||||
|
||||
# Enable audio (loads snd_bcm2835)
|
||||
dtparam=audio=on
|
||||
hdmi_force_hotplug=1
|
||||
dtparam=i2c_arm=on
|
||||
dtparam=spi=on
|
||||
enable_uart=1
|
||||
dtoverlay=mhs35:rotate=90
|
||||
hdmi_group=2
|
||||
hdmi_mode=1
|
||||
hdmi_mode=87
|
||||
hdmi_cvt 480 320 60 6 0 0 0
|
||||
hdmi_drive=2
|
||||
|
|
@ -0,0 +1,23 @@
|
|||
#!/bin/sh -e
|
||||
#
|
||||
# rc.local
|
||||
#
|
||||
# This script is executed at the end of each multiuser runlevel.
|
||||
# Make sure that the script will "exit 0" on success or any other
|
||||
# value on error.
|
||||
#
|
||||
# In order to enable or disable this script just change the execution
|
||||
# bits.
|
||||
#
|
||||
# By default this script does nothing.
|
||||
|
||||
# Print the IP address
|
||||
_IP=$(hostname -I) || true
|
||||
if [ "$_IP" ]; then
|
||||
printf "My IP address is %s\n" "$_IP"
|
||||
fi
|
||||
|
||||
sleep 7
|
||||
fbcp &
|
||||
|
||||
exit 0
|
||||
|
|
@ -0,0 +1,20 @@
|
|||
#!/bin/sh -e
|
||||
#
|
||||
# rc.local
|
||||
#
|
||||
# This script is executed at the end of each multiuser runlevel.
|
||||
# Make sure that the script will "exit 0" on success or any other
|
||||
# value on error.
|
||||
#
|
||||
# In order to enable or disable this script just change the execution
|
||||
# bits.
|
||||
#
|
||||
# By default this script does nothing.
|
||||
|
||||
# Print the IP address
|
||||
_IP=$(hostname -I) || true
|
||||
if [ "$_IP" ]; then
|
||||
printf "My IP address is %s\n" "$_IP"
|
||||
fi
|
||||
|
||||
exit 0
|
||||
|
|
@ -0,0 +1,167 @@
|
|||
#!/bin/bash
|
||||
cur_dir=`pwd`
|
||||
if [ ! -f $cur_dir/.have_installed ]; then
|
||||
echo "Please install the LCD driver first"
|
||||
echo "Usage: sudo ./xxx-show. xxx: MHS35,LCD35,MPI3508 etc."
|
||||
exit
|
||||
fi
|
||||
|
||||
print_info()
|
||||
{
|
||||
echo "Usage:sudo ./rotate.sh [0] [90] [180] [270] [360] [450]"
|
||||
echo "0-Screen rotation 0 degrees"
|
||||
echo "90-Screen rotation 90 degrees"
|
||||
echo "180-Screen rotation 180 degrees"
|
||||
echo "270-Screen rotation 270 degrees"
|
||||
echo "360-Screen flip horizontal(Valid only for HDMI screens)"
|
||||
echo "450-Screen flip vertical(Valid only for HDMI screens)"
|
||||
}
|
||||
|
||||
if [ $# -eq 0 ]; then
|
||||
echo "Please input parameter:0,90,180,270,360,450"
|
||||
print_info
|
||||
exit
|
||||
elif [ $# -eq 1 ]; then
|
||||
if [ ! -n "$(echo $1| sed -n "/^[0-9]\+$/p")" ]; then
|
||||
echo "Invalid parameter"
|
||||
print_info
|
||||
exit
|
||||
else
|
||||
if [ $1 -ne 0 ] && [ $1 -ne 90 ] && [ $1 -ne 180 ] && [ $1 -ne 270 ] && [ $1 -ne 360 ] && [ $1 -ne 450 ]; then
|
||||
echo "Invalid parameter"
|
||||
print_info
|
||||
exit
|
||||
fi
|
||||
fi
|
||||
else
|
||||
echo "Too many parameters, only one parameter allowed"
|
||||
exit
|
||||
fi
|
||||
|
||||
#get screen parameter
|
||||
tmp=`cat $cur_dir/.have_installed`
|
||||
output_type=`cat $cur_dir/.have_installed | awk -F ':' '{printf $1}'`
|
||||
touch_type=`cat $cur_dir/.have_installed | awk -F ':' '{printf $2}'`
|
||||
device_id=`cat $cur_dir/.have_installed | awk -F ':' '{printf $3}'`
|
||||
default_value=`cat $cur_dir/.have_installed | awk -F ':' '{printf $4}'`
|
||||
|
||||
if [ $output_type = "hdmi" ]; then
|
||||
result=`grep -rn "^display_rotate=" /boot/config.txt | tail -n 1`
|
||||
line=`echo -n $result | awk -F: '{printf $1}'`
|
||||
str=`echo -n $result | awk -F: '{printf $NF}'`
|
||||
old_rotate_value=`echo -n $result | awk -F= '{printf $NF}'`
|
||||
if [ $old_rotate_value = "0x10000" ]; then
|
||||
old_rotate_value=4
|
||||
elif [ $old_rotate_value = "0x20000" ]; then
|
||||
old_rotate_value=5
|
||||
fi
|
||||
if [ $1 -eq 0 ] || [ $1 -eq 90 ] || [ $1 -eq 180 ] || [ $1 -eq 270 ]; then
|
||||
new_rotate_value=$[(($default_value+$1)%360)/90]
|
||||
else
|
||||
new_rotate_value=$[$1/90]
|
||||
fi
|
||||
elif [ $output_type = "gpio" ]; then
|
||||
result=`grep -rn "^dtoverlay=" /boot/config.txt | grep ":rotate=" | tail -n 1`
|
||||
line=`echo -n $result | awk -F: '{printf $1}'`
|
||||
str=`echo -n $result | awk -F: '{printf $NF}'`
|
||||
old_rotate_value=`echo -n $result | awk -F= '{printf $NF}'`
|
||||
if [ $1 -eq 0 ] || [ $1 -eq 90 ] || [ $1 -eq 180 ] || [ $1 -eq 270 ]; then
|
||||
new_rotate_value=$[($default_value+$1)%360]
|
||||
else
|
||||
echo "Invalid parameter: only for HDMI screens"
|
||||
exit
|
||||
fi
|
||||
else
|
||||
echo "Invalid output type"
|
||||
exit
|
||||
fi
|
||||
|
||||
if [ $old_rotate_value -eq $new_rotate_value ]; then
|
||||
if [ $output_type = "hdmi" ]; then
|
||||
if [ $1 -eq 0 ] || [ $1 -eq 90 ] || [ $1 -eq 180 ] || [ $1 -eq 270 ]; then
|
||||
old_rotate_value=$[($old_rotate_value*90+360-$default_value)%360]
|
||||
else
|
||||
old_rotate_value=$[$old_rotate_value*90]
|
||||
fi
|
||||
elif [ $output_type = "gpio" ]; then
|
||||
old_rotate_value=$[($old_rotate_value+360-$default_value)%360]
|
||||
fi
|
||||
echo "Current rotate value is $old_rotate_value"
|
||||
exit
|
||||
fi
|
||||
|
||||
#setting LCD rotate
|
||||
if [ $output_type = "hdmi" ]; then
|
||||
if [ $new_rotate_value -eq 4 ]; then
|
||||
sudo sed -i -e ''"$line"'s/'"$str"'/display_rotate=0x10000/' /boot/config.txt
|
||||
elif [ $new_rotate_value -eq 5 ]; then
|
||||
sudo sed -i -e ''"$line"'s/'"$str"'/display_rotate=0x20000/' /boot/config.txt
|
||||
else
|
||||
sudo sed -i -e ''"$line"'s/'"$str"'/display_rotate='"$new_rotate_value"'/' /boot/config.txt
|
||||
fi
|
||||
new_rotate_value=$[$new_rotate_value*90]
|
||||
elif [ $output_type = "gpio" ]; then
|
||||
sudo sed -i -e ''"$line"'s/'"$str"'/rotate='"$new_rotate_value"'/' /boot/config.txt
|
||||
resultr=`grep -rn "^hdmi_cvt" /boot/config.txt | tail -n 1 | awk -F' ' '{print $1,$2,$3}'`
|
||||
liner=`echo -n $resultr | awk -F: '{printf $1}'`
|
||||
strr=`echo -n $resultr | awk -F: '{printf $2}'`
|
||||
if [ $new_rotate_value -eq $default_value ] || [ $new_rotate_value -eq $[($default_value+180+360)%360] ]; then
|
||||
sudo sed -i -e ''"$liner"'s/'"$strr"'/hdmi_cvt 480 320/' /boot/config.txt
|
||||
elif [ $new_rotate_value -eq $[($default_value-90+360)%360] ] || [ $new_rotate_value -eq $[($default_value+90+360)%360] ]; then
|
||||
sudo sed -i -e ''"$liner"'s/'"$strr"'/hdmi_cvt 320 480/' /boot/config.txt
|
||||
fi
|
||||
fi
|
||||
|
||||
#setting touch screen rotate
|
||||
if [ $touch_type = "resistance" ]; then
|
||||
if [ $new_rotate_value -eq 0 ]; then
|
||||
cp $cur_dir/usr/99-calibration.conf-$device_id-0 /etc/X11/xorg.conf.d/99-calibration.conf
|
||||
echo "LCD rotate value is set to $1"
|
||||
elif [ $new_rotate_value -eq 90 ]; then
|
||||
cp $cur_dir/usr/99-calibration.conf-$device_id-90 /etc/X11/xorg.conf.d/99-calibration.conf
|
||||
echo "LCD rotate value is set to $1"
|
||||
elif [ $new_rotate_value -eq 180 ]; then
|
||||
cp $cur_dir/usr/99-calibration.conf-$device_id-180 /etc/X11/xorg.conf.d/99-calibration.conf
|
||||
echo "LCD rotate value is set to $1"
|
||||
elif [ $new_rotate_value -eq 270 ]; then
|
||||
cp $cur_dir/usr/99-calibration.conf-$device_id-270 /etc/X11/xorg.conf.d/99-calibration.conf
|
||||
echo "LCD rotate value is set to $1"
|
||||
elif [ $new_rotate_value -eq 360 ]; then
|
||||
cp $cur_dir/usr/99-calibration.conf-$device_id-FLIP-H /etc/X11/xorg.conf.d/99-calibration.conf
|
||||
echo "LCD rotate value is set to flip horizontally"
|
||||
elif [ $new_rotate_value -eq 450 ]; then
|
||||
cp $cur_dir/usr/99-calibration.conf-$device_id-FLIP-V /etc/X11/xorg.conf.d/99-calibration.conf
|
||||
echo "LCD rotate value is set to flip vertically"
|
||||
fi
|
||||
elif [ $touch_type = "capacity" ]; then
|
||||
if [ $new_rotate_value -eq 0 ]; then
|
||||
cp $cur_dir/usr/40-libinput.conf-0 /etc/X11/xorg.conf.d/40-libinput.conf
|
||||
echo "LCD rotate value is set to $1"
|
||||
elif [ $new_rotate_value -eq 90 ]; then
|
||||
cp $cur_dir/usr/40-libinput.conf-90 /etc/X11/xorg.conf.d/40-libinput.conf
|
||||
echo "LCD rotate value is set to $1"
|
||||
elif [ $new_rotate_value -eq 180 ]; then
|
||||
cp $cur_dir/usr/40-libinput.conf-180 /etc/X11/xorg.conf.d/40-libinput.conf
|
||||
echo "LCD rotate value is set to $1"
|
||||
elif [ $new_rotate_value -eq 270 ]; then
|
||||
cp $cur_dir/usr/40-libinput.conf-270 /etc/X11/xorg.conf.d/40-libinput.conf
|
||||
echo "LCD rotate value is set to $1"
|
||||
elif [ $new_rotate_value -eq 360 ]; then
|
||||
cp $cur_dir/usr/40-libinput.conf-FLIP-H /etc/X11/xorg.conf.d/40-libinput.conf
|
||||
echo "LCD rotate value is set to flip horizontally"
|
||||
elif [ $new_rotate_value -eq 450 ]; then
|
||||
cp $cur_dir/usr/40-libinput.conf-FLIP-V /etc/X11/xorg.conf.d/40-libinput.conf
|
||||
echo "LCD rotate value is set to flip vertically"
|
||||
fi
|
||||
else
|
||||
echo "Invalid touch type"
|
||||
exit
|
||||
fi
|
||||
|
||||
sudo sync
|
||||
sudo sync
|
||||
|
||||
echo "reboot now"
|
||||
sleep 1
|
||||
sudo reboot
|
||||
|
||||
|
|
@ -0,0 +1 @@
|
|||
Subproject commit af8d32246c23cb23e4030e6588668a14341f5ddc
|
||||
|
|
@ -0,0 +1,75 @@
|
|||
#!/bin/bash
|
||||
if [ ! -d "./.system_backup" ]; then
|
||||
sudo mkdir ./.system_backup
|
||||
fi
|
||||
|
||||
sudo rm -rf ./.system_backup/*
|
||||
|
||||
if [ -f /etc/X11/xorg.conf.d/99-calibration.conf ]; then
|
||||
sudo cp -rf /etc/X11/xorg.conf.d/99-calibration.conf ./.system_backup
|
||||
sudo rm -rf /etc/X11/xorg.conf.d/99-calibration.conf
|
||||
fi
|
||||
|
||||
if [ -f /etc/X11/xorg.conf.d/40-libinput.conf ]; then
|
||||
sudo cp -rf /etc/X11/xorg.conf.d/40-libinput.conf ./.system_backup
|
||||
sudo rm -rf /etc/X11/xorg.conf.d/40-libinput.conf
|
||||
fi
|
||||
|
||||
if [ -d /etc/X11/xorg.conf.d ]; then
|
||||
sudo mkdir -p ./.system_backup/xorg.conf.d
|
||||
sudo rm -rf /etc/X11/xorg.conf.d
|
||||
fi
|
||||
|
||||
result=`grep -rn "^dtoverlay=" /boot/config.txt | grep ":rotate=" | tail -n 1`
|
||||
if [ $? -eq 0 ]; then
|
||||
str=`echo -n $result | awk -F: '{printf $2}' | awk -F= '{printf $NF}'`
|
||||
if [ -f /boot/overlays/$str-overlay.dtb ]; then
|
||||
sudo cp -rf /boot/overlays/$str-overlay.dtb ./.system_backup
|
||||
sudo rm -rf /boot/overlays/$str-overlay.dtb
|
||||
fi
|
||||
if [ -f /boot/overlays/$str.dtbo ]; then
|
||||
sudo cp -rf /boot/overlays/$str.dtbo ./.system_backup
|
||||
sudo rm -rf /boot/overlays/$str.dtbo
|
||||
fi
|
||||
fi
|
||||
|
||||
sudo cp -rf /boot/config.txt ./.system_backup
|
||||
sudo cp -rf /usr/share/X11/xorg.conf.d/99-fbturbo.conf ./.system_backup/
|
||||
sudo cp -rf /boot/cmdline.txt ./.system_backup/
|
||||
sudo cp -rf /etc/rc.local ./.system_backup/
|
||||
|
||||
if [ -f /etc/inittab ]; then
|
||||
sudo cp -rf /etc/inittab ./.system_backup
|
||||
sudo rm -rf /etc/inittab
|
||||
fi
|
||||
|
||||
type fbcp > /dev/null 2>&1
|
||||
if [ $? -eq 0 ]; then
|
||||
sudo touch ./.system_backup/have_fbcp
|
||||
sudo rm -rf /usr/local/bin/fbcp
|
||||
fi
|
||||
|
||||
#type cmake > /dev/null 2>&1
|
||||
#if [ $? -eq 0 ]; then
|
||||
#sudo touch ./.system_backup/have_cmake
|
||||
#sudo apt-get purge cmake -y 2> error_output.txt
|
||||
#result=`cat ./error_output.txt`
|
||||
#echo -e "\033[31m$result\033[0m"
|
||||
#fi
|
||||
|
||||
if [ -f /usr/share/X11/xorg.conf.d/10-evdev.conf ]; then
|
||||
sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf ./.system_backup
|
||||
sudo dpkg -P xserver-xorg-input-evdev
|
||||
#sudo apt-get purge xserver-xorg-input-evdev -y 2> error_output.txt
|
||||
#result=`cat ./error_output.txt`
|
||||
#echo -e "\033[31m$result\033[0m"
|
||||
fi
|
||||
|
||||
if [ -f /usr/share/X11/xorg.conf.d/45-evdev.conf ]; then
|
||||
sudo cp -rf /usr/share/X11/xorg.conf.d/45-evdev.conf ./.system_backup
|
||||
sudo rm -rf /usr/share/X11/xorg.conf.d/45-evdev.conf
|
||||
fi
|
||||
|
||||
if [ -f ./.have_installed ]; then
|
||||
sudo cp -rf ./.have_installed ./.system_backup
|
||||
fi
|
||||
|
|
@ -0,0 +1,93 @@
|
|||
#!/bin/bash
|
||||
#Just finished the system, no need to restore
|
||||
if [ ! -d "./.system_backup" ]; then
|
||||
echo "The system is the original version and does not need to be restored"
|
||||
exit
|
||||
fi
|
||||
|
||||
if [ -d /etc/X11/xorg.conf.d ]; then
|
||||
sudo rm -rf /etc/X11/xorg.conf.d
|
||||
fi
|
||||
if [ -d ./.system_backup/xorg.conf.d ]; then
|
||||
sudo cp -rf ./.system_backup/xorg.conf.d /etc/X11
|
||||
if [ -f ./.system_backup/99-calibration.conf ]; then
|
||||
sudo cp -rf ./.system_backup/99-calibration.conf /etc/X11/xorg.conf.d
|
||||
fi
|
||||
if [ -f ./.system_backup/40-libinput.conf ]; then
|
||||
sudo cp -rf ./.system_backup/40-libinput.conf /etc/X11/xorg.conf.d
|
||||
fi
|
||||
fi
|
||||
|
||||
result=`grep -rn "^dtoverlay=" /boot/config.txt | grep ":rotate=" | tail -n 1`
|
||||
if [ $? -eq 0 ]; then
|
||||
str=`echo -n $result | awk -F: '{printf $2}' | awk -F= '{printf $NF}'`
|
||||
sudo rm -rf /boot/overlays/$str-overlay.dtb
|
||||
sudo rm -rf /boot/overlays/$str.dtbo
|
||||
fi
|
||||
ls -al ./.system_backup/*.dtb > /dev/null 2>&1 && sudo cp -rf ./.system_backup/*.dtb /boot/overlays/
|
||||
ls -al ./.system_backup/*.dtbo > /dev/null 2>&1 && sudo cp -rf ./.system_backup/*.dtbo /boot/overlays/
|
||||
|
||||
sudo cp -rf ./.system_backup/99-fbturbo.conf /usr/share/X11/xorg.conf.d
|
||||
sudo cp -rf ./.system_backup/cmdline.txt /boot/
|
||||
sudo cp -rf ./.system_backup/config.txt /boot/
|
||||
sudo cp -rf ./.system_backup/rc.local /etc/
|
||||
|
||||
if [ -f /etc/inittab ]; then
|
||||
sudo rm -rf /etc/inittab
|
||||
fi
|
||||
if [ -f ./.system_backup/inittab ]; then
|
||||
sudo cp -rf ./.system_backup/inittab /etc
|
||||
fi
|
||||
|
||||
type fbcp > /dev/null 2>&1
|
||||
if [ $? -eq 0 ]; then
|
||||
sudo rm -rf /usr/local/bin/fbcp
|
||||
fi
|
||||
if [ -f ./.system_backup/have_fbcp ]; then
|
||||
sudo install ./rpi-fbcp/build/fbcp /usr/local/bin/fbcp
|
||||
fi
|
||||
|
||||
#type cmake > /dev/null 2>&1
|
||||
#if [ $? -eq 0 ]; then
|
||||
#sudo apt-get purge cmake -y 2> error_output.txt
|
||||
#result=`cat ./error_output.txt`
|
||||
#echo -e "\033[31m$result\033[0m"
|
||||
#fi
|
||||
#if [ -f ./.system_backup/have_cmake ]; then
|
||||
#sudo apt-get install cmake -y 2> error_output.txt
|
||||
#result=`cat ./error_output.txt`
|
||||
#echo -e "\033[31m$result\033[0m"
|
||||
#fi
|
||||
|
||||
if [ -f /usr/share/X11/xorg.conf.d/10-evdev.conf ]; then
|
||||
sudo dpkg -P xserver-xorg-input-evdev
|
||||
#sudo apt-get purge xserver-xorg-input-evdev -y 2> error_output.txt
|
||||
#result=`cat ./error_output.txt`
|
||||
#echo -e "\033[31m$result\033[0m"
|
||||
fi
|
||||
if [ -f ./.system_backup/10-evdev.conf ]; then
|
||||
sudo dpkg -i -B ./xserver-xorg-input-evdev_2.10.5-1_armhf.deb
|
||||
#sudo apt-get install xserver-xorg-input-evdev -y 2> error_output.txt
|
||||
#result=`cat ./error_output.txt`
|
||||
#echo -e "\033[31m$result\033[0m"
|
||||
fi
|
||||
|
||||
if [ -f /usr/share/X11/xorg.conf.d/45-evdev.conf ]; then
|
||||
sudo rm -rf /usr/share/X11/xorg.conf.d/45-evdev.conf
|
||||
fi
|
||||
if [ -f ./.system_backup/45-evdev.conf ]; then
|
||||
sudo cp -rf ./.system_backup/45-evdev.conf /usr/share/X11/xorg.conf.d
|
||||
fi
|
||||
|
||||
if [ -f ./.system_backup/.have_installed ]; then
|
||||
sudo cp -rf ./.system_backup/.have_installed ./
|
||||
fi
|
||||
|
||||
sudo sync
|
||||
sudo sync
|
||||
|
||||
echo "The system has been restored"
|
||||
echo "now reboot"
|
||||
sleep 1
|
||||
|
||||
sudo reboot
|
||||
|
|
@ -0,0 +1,36 @@
|
|||
# Match on all types of devices but tablet devices and joysticks
|
||||
Section "InputClass"
|
||||
Identifier "libinput pointer catchall"
|
||||
MatchIsPointer "on"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
||||
Section "InputClass"
|
||||
Identifier "libinput keyboard catchall"
|
||||
MatchIsKeyboard "on"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
||||
Section "InputClass"
|
||||
Identifier "libinput touchpad catchall"
|
||||
MatchIsTouchpad "on"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
||||
Section "InputClass"
|
||||
Identifier "libinput touchscreen catchall"
|
||||
MatchIsTouchscreen "on"
|
||||
Option "CalibrationMatrix" "-1 0 1 0 -1 1 0 0 1"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
||||
Section "InputClass"
|
||||
Identifier "libinput tablet catchall"
|
||||
MatchIsTablet "on"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
|
@ -0,0 +1,36 @@
|
|||
# Match on all types of devices but tablet devices and joysticks
|
||||
Section "InputClass"
|
||||
Identifier "libinput pointer catchall"
|
||||
MatchIsPointer "on"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
||||
Section "InputClass"
|
||||
Identifier "libinput keyboard catchall"
|
||||
MatchIsKeyboard "on"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
||||
Section "InputClass"
|
||||
Identifier "libinput touchpad catchall"
|
||||
MatchIsTouchpad "on"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
||||
Section "InputClass"
|
||||
Identifier "libinput touchscreen catchall"
|
||||
MatchIsTouchscreen "on"
|
||||
Option "CalibrationMatrix" "0 -1 1 1 0 0 0 0 1"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
||||
Section "InputClass"
|
||||
Identifier "libinput tablet catchall"
|
||||
MatchIsTablet "on"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
|
@ -0,0 +1,36 @@
|
|||
# Match on all types of devices but tablet devices and joysticks
|
||||
Section "InputClass"
|
||||
Identifier "libinput pointer catchall"
|
||||
MatchIsPointer "on"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
||||
Section "InputClass"
|
||||
Identifier "libinput keyboard catchall"
|
||||
MatchIsKeyboard "on"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
||||
Section "InputClass"
|
||||
Identifier "libinput touchpad catchall"
|
||||
MatchIsTouchpad "on"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
||||
Section "InputClass"
|
||||
Identifier "libinput touchscreen catchall"
|
||||
MatchIsTouchscreen "on"
|
||||
Option "CalibrationMatrix" "0 1 0 -1 0 1 0 0 1"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
||||
Section "InputClass"
|
||||
Identifier "libinput tablet catchall"
|
||||
MatchIsTablet "on"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
|
@ -0,0 +1,36 @@
|
|||
# Match on all types of devices but tablet devices and joysticks
|
||||
Section "InputClass"
|
||||
Identifier "libinput pointer catchall"
|
||||
MatchIsPointer "on"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
||||
Section "InputClass"
|
||||
Identifier "libinput keyboard catchall"
|
||||
MatchIsKeyboard "on"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
||||
Section "InputClass"
|
||||
Identifier "libinput touchpad catchall"
|
||||
MatchIsTouchpad "on"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
||||
Section "InputClass"
|
||||
Identifier "libinput touchscreen catchall"
|
||||
MatchIsTouchscreen "on"
|
||||
Option "CalibrationMatrix" "-1 0 1 0 1 0 0 0 1"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
||||
Section "InputClass"
|
||||
Identifier "libinput tablet catchall"
|
||||
MatchIsTablet "on"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
|
@ -0,0 +1,36 @@
|
|||
# Match on all types of devices but tablet devices and joysticks
|
||||
Section "InputClass"
|
||||
Identifier "libinput pointer catchall"
|
||||
MatchIsPointer "on"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
||||
Section "InputClass"
|
||||
Identifier "libinput keyboard catchall"
|
||||
MatchIsKeyboard "on"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
||||
Section "InputClass"
|
||||
Identifier "libinput touchpad catchall"
|
||||
MatchIsTouchpad "on"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
||||
Section "InputClass"
|
||||
Identifier "libinput touchscreen catchall"
|
||||
MatchIsTouchscreen "on"
|
||||
Option "CalibrationMatrix" "1 0 0 0 -1 1 0 0 1"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
||||
Section "InputClass"
|
||||
Identifier "libinput tablet catchall"
|
||||
MatchIsTablet "on"
|
||||
MatchDevicePath "/dev/input/event*"
|
||||
Driver "libinput"
|
||||
EndSection
|
||||
|
|
@ -0,0 +1,6 @@
|
|||
Section "InputClass"
|
||||
Identifier "calibration"
|
||||
MatchProduct "ADS7846 Touchscreen"
|
||||
Option "Calibration" "72 3916 182 4012"
|
||||
Option "SwapAxes" "0"
|
||||
EndSection
|
||||
|
|
@ -0,0 +1,6 @@
|
|||
Section "InputClass"
|
||||
Identifier "calibration"
|
||||
MatchProduct "ADS7846 Touchscreen"
|
||||
Option "Calibration" "3916 72 4012 182"
|
||||
Option "SwapAxes" "0"
|
||||
EndSection
|
||||
|
|
@ -1,6 +1,6 @@
|
|||
Section "InputClass"
|
||||
Identifier "calibration"
|
||||
MatchProduct "ADS7846 Touchscreen"
|
||||
Option "Calibration" "3865 158 289 3873"
|
||||
Option "Calibration" "4012 182 72 3916"
|
||||
Option "SwapAxes" "1"
|
||||
EndSection
|
||||
|
|
@ -0,0 +1,6 @@
|
|||
Section "InputClass"
|
||||
Identifier "calibration"
|
||||
MatchProduct "ADS7846 Touchscreen"
|
||||
Option "Calibration" "182 4012 3916 72"
|
||||
Option "SwapAxes" "1"
|
||||
EndSection
|
||||
|
|
@ -0,0 +1,6 @@
|
|||
Section "InputClass"
|
||||
Identifier "calibration"
|
||||
MatchProduct "ADS7846 Touchscreen"
|
||||
Option "Calibration" "3916 72 182 4012"
|
||||
Option "SwapAxes" "0"
|
||||
EndSection
|
||||
|
|
@ -0,0 +1,6 @@
|
|||
Section "InputClass"
|
||||
Identifier "calibration"
|
||||
MatchProduct "ADS7846 Touchscreen"
|
||||
Option "Calibration" "72 3916 4012 182"
|
||||
Option "SwapAxes" "0"
|
||||
EndSection
|
||||
|
|
@ -0,0 +1,9 @@
|
|||
Section "InputClass"
|
||||
Identifier "calibration"
|
||||
MatchProduct "ADS7846 Touchscreen"
|
||||
Option "Calibration" "3697 135 136 3839"
|
||||
Option "SwapAxes" "1"
|
||||
Option "EmulateThirdButton" "1"
|
||||
Option "EmulateThirdButtonTimeout" "1000"
|
||||
Option "EmulateThirdButtonMoveThreshold" "300"
|
||||
EndSection
|
||||
|
|
@ -0,0 +1,9 @@
|
|||
Section "InputClass"
|
||||
Identifier "calibration"
|
||||
MatchProduct "ADS7846 Touchscreen"
|
||||
Option "Calibration" "3713 158 3901 212"
|
||||
Option "SwapAxes" "1"
|
||||
Option "EmulateThirdButton" "1"
|
||||
Option "EmulateThirdButtonTimeout" "1000"
|
||||
Option "EmulateThirdButtonMoveThreshold" "300"
|
||||
EndSection
|
||||
|
|
@ -0,0 +1,9 @@
|
|||
Section "InputClass"
|
||||
Identifier "calibration"
|
||||
MatchProduct "ADS7846 Touchscreen"
|
||||
Option "Calibration" "268 3880 227 3936"
|
||||
Option "SwapAxes" "0"
|
||||
Option "EmulateThirdButton" "1"
|
||||
Option "EmulateThirdButtonTimeout" "1000"
|
||||
Option "EmulateThirdButtonMoveThreshold" "300"
|
||||
EndSection
|
||||
|
|
@ -0,0 +1,9 @@
|
|||
Section "InputClass"
|
||||
Identifier "calibration"
|
||||
MatchProduct "ADS7846 Touchscreen"
|
||||
Option "Calibration" "3880 268 3936 227"
|
||||
Option "SwapAxes" "0"
|
||||
Option "EmulateThirdButton" "1"
|
||||
Option "EmulateThirdButtonTimeout" "1000"
|
||||
Option "EmulateThirdButtonMoveThreshold" "300"
|
||||
EndSection
|
||||
|
|
@ -0,0 +1,9 @@
|
|||
Section "InputClass"
|
||||
Identifier "calibration"
|
||||
MatchProduct "ADS7846 Touchscreen"
|
||||
Option "Calibration" "227 3936 3880 268"
|
||||
Option "SwapAxes" "1"
|
||||
Option "EmulateThirdButton" "1"
|
||||
Option "EmulateThirdButtonTimeout" "1000"
|
||||
Option "EmulateThirdButtonMoveThreshold" "300"
|
||||
EndSection
|
||||
|
|
@ -0,0 +1,9 @@
|
|||
Section "InputClass"
|
||||
Identifier "calibration"
|
||||
MatchProduct "ADS7846 Touchscreen"
|
||||
Option "Calibration" "3936 227 268 3880"
|
||||
Option "SwapAxes" "1"
|
||||
Option "EmulateThirdButton" "1"
|
||||
Option "EmulateThirdButtonTimeout" "1000"
|
||||
Option "EmulateThirdButtonMoveThreshold" "300"
|
||||
EndSection
|
||||
|
|
@ -0,0 +1,9 @@
|
|||
Section "InputClass"
|
||||
Identifier "calibration"
|
||||
MatchProduct "ADS7846 Touchscreen"
|
||||
Option "Calibration" "3936 227 268 3880"
|
||||
Option "SwapAxes" "1"
|
||||
Option "EmulateThirdButton" "1"
|
||||
Option "EmulateThirdButtonTimeout" "1000"
|
||||
Option "EmulateThirdButtonMoveThreshold" "300"
|
||||
EndSection
|
||||
|
|
@ -0,0 +1,16 @@
|
|||
# This is a minimal sample config file, which can be copied to
|
||||
# /etc/X11/xorg.conf in order to make the Xorg server pick up
|
||||
# and load xf86-video-fbturbo driver installed in the system.
|
||||
#
|
||||
# When troubleshooting, check /var/log/Xorg.0.log for the debugging
|
||||
# output and error messages.
|
||||
# Run "man fbturbo" to get additional information about the extra
|
||||
# configuration options for tuning the driver.
|
||||
|
||||
Section "Device"
|
||||
Identifier "Allwinner A10/A13/A20 FBDEV"
|
||||
Driver "fbturbo"
|
||||
Option "fbdev" "/dev/fb0"
|
||||
|
||||
Option "SwapbuffersWait" "true"
|
||||
EndSection
|
||||
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Loading…
Reference in New Issue